AQUELLUX S Water Repellent for External Masonry Substrates

SILANE/SILOXANE SOLVENT-BASED WATER REPELLENT

A silane/siloxane solvent-based water repellent for external use that does not alter the appearance of the surface (some slight surface colour change can occur depending on the porosity and type of substrate).
Used to make concrete, brick, stone, and other mineral surfaces water repellent whilst allowing trapped moisture to escape from the substrate.

Excellent penetration depth. Highly stable on concrete and other surfaces containing cement.

AQUELLUX S is used to treat vertical and inclined surfaces such as walls and roofs.
Use AQUELLUX S on concrete, cement plaster, block work, bricks, roofing tiles, cement asbestos and fibrous cement, GRC panels and natural stone (test substrate for suitability before use).
Porous concrete blocks may not be suitable for treatment.

Coverage:
As a guide concrete blocks and porous stone: up to 1m2/lt
normal concrete 2 – 3m2/lt, dense concrete and brick up to 6m2/lt.

Packaging:
1 & 4 litre cans, 20 & 210 litre drums

 Click here to download technical datasheet

Click here to watch how an old concrete block wall treated with AQUELLUX S repels water.

AQUELLUX S treated surfaces repel water but do not block the pores, allowing trapped moisture to escape.

AQUELLUX S will bridge hairline cracks in the substrate.

Questions & Answers

Q: Is AQUELLUX S (or SILAC or AQUELLUX S WB) a waterproof coating?
A: No. AQUELLUX S (SILAC and AQUELLUX S WB) are specialized silicone water repellents. Unlike a paint or similar product, they do not form a film on the surface to which they are applied, but instead line the pores and capillaries with a silicone material that interferes with the ability of water droplets to wet into the substrate. This allows the substrate to "breathe" and release trapped moisture within the substrate back to the atmosphere. The downside to silicone water repellents is that under certain conditions including continual rain, wind driven rain or when applied to very porous substrates, the water repellency effect may be overcome and the substrate becomes wet. Note that as soon as the water stops contacting the substrate, the water repellent will allow the moisture to escape back to the atmosphere.

Q: Can I use AQUELLUX S on very porous substrates?
A: Yes, but the suitability of AQUELLUX S on these substrates and the quantity required must be checked. Very porous substrates include concrete block (especially with pumice filler) and Oamaru Stone. Generally, treat the surface with AQUELLUX S at up to 1 square metre per litre. In some cases, the substrate may be too porous (the pores and capillaries are too wide) to successfully treat with AQUELLUX S and therefore the water repellency may be overcome. It is highly advisable to test the proposed substrate to be treated with AQUELLUX S to determine suitability. Also, for concrete blocks requiring sealing, refer to our CONCRETE BLOCK SEALER System.

Q: Will AQUELLUX S alter the appearance of the substrate?
A: Under most circumstances, there will be no visible change in the substrate due to the application of AQUELLUX S as there is no film to modify the appearance. However, in some cases, as the AQUELLUX S allows the substrate to dry out (whether relatively new or old), then the substrate can change in colour at different rates. This effect is due to the substrate and because the AQUELLUX S doesn't create a film, the substrate colour changes are apparent. In addition, any stains or colour differences apparent in the substrate will be apparent after the application of AQUELLUX S, so must be removed prior to treatment. Furthermore, substrates that are not uniform in porosity and/or are very dense may result in AQUELLUX S silicone appearing at the surface of the substrate and may result in a noticeable colour change. It is recommended that a small area of the surface to be treated is tested for any potential colour change and application rate.

When applying AQUELLUX S to any surface, the solvent carrier of AQUELLUX S may flush out impurities in the substrate (including dirt, dust - especially if Oamaru Stone is sanded, etc) or may react with fillers and additives incorporated into grout or plaster mixes. Ensure all surfaces are thoroughly cleaned before application and allowed to age for at least 28 days for fresh concrete and mortar. Test an area before proceeding with complete application.

Q: I've noticed that the treated surface doesn't show as much beading effect as before when wet. Is this normal?
A: Yes. A proper treatment of AQUELLUX S requires the correct quantity of product be applied to the substrate depending on porosity. As the AQUELLUX S is applied, it penetrates into the substrate. Over time, the effects of weathering reduce the surface effect of beading, however the water is not able to "wet" into the substrate because of the silicone lining the pores and capillaries. Therefore, assuming the substrate is not too porous and therefore unsuitable for treatment, the AQUELLUX S treatment will continue to do its work within the substrate. Additional coats of AQUELLUX S may be applied as and if required.

Q: What's the difference between AQUELLUX S and SILAC?
A: SILAC is an acrylic modified form of AQUELLUX S. It is primarily designed for use on more porous substrates, particularly Oamaru Stone. When applied to Oamaru Stone, SILAC helps to bind together the stone's surface, thereby imparting extra strength and helping to increase the effectiveness of the water repellent treatment. However, there will be a change in the appearance of the substrate when using SILAC compared to AQUELLUX S. When AQUELLUX S is applied to Oamaru Stone, the pores and capillaries of the stone are still lined, however, there is no physical resistance to wearing. If the stone dusts when rubbed, then this slowly removes the AQUELLUX S treatment from the stone as the stone weathers. SILAC can be applied to concrete (including polished or honed concrete) where the surface may be too porous for successful treatment using AQUELLUX S.

Q: Can AQUELLUX S be applied to a horizontal surface.
A: Yes, however we do not recommend it as the results may not be as required. AQUELLUX S should be applied to a surface that is inclined or vertical to ensure that the water can run off. If water can pond on the surface, then it may eventually be able to overcome the water repellency effect of AQUELLUX S and penetrate into the substrate. In some circumstances, such as treating concrete pavers or external concrete where there is no habitable/storage space below (such as concrete paths or on-ground concrete decks) or on exposed aggregate surfaces (on ground) where a natural look is required, AQUELLUX S may be applied. Note that the water will pool on the surfaces and therefore they may be slippery when wet. It is important to test AQUELLUX S on the surface prior to proceeding with the treatment to determine coverage rate and any potential colour change. The effectiveness and length of time that water repellency will remain for AQUELLUX S when applied to horizontal surfaces is the sole responsiblity of the applicator/specifier/owner.

Q: Can AQUELLUX S be applied to the outside of a substrate that is back-filled? Can it be applied to the inside of a wall that is leaking?
A: No. AQUELLUX S is not a waterproof coating and is not designed to be under constant hydrostatic pressure. For an external wall that requires a waterproof coating, please refer to BITUGUARD. AQUELLUX S is not suitable for application to an interior wall that has water or moisture passing from the outside to the inside because the water/moisture will pass through the AQUELLUX S. Apply the AQUELLUX S to the outside of the wall. Water must contact the AQUELLUX S treatment from the front face to which it is applied.

Please read the product datasheet for additional important information.

Please contact us if you have any application specific questions regarding AQUELLUX , SILAC or AQUELLUX S WB.

This website provides brief product descriptions of our products. Information is included for illustrative purposes only. It is not a product application guide. Do not use or specify our products without following the printed application guidelines on the current technical data sheets, product labels, material safety data sheets and any other supporting literature. We reserve the right to alter formulations without notice. Properties as stated were determined under controlled laboratory conditions. We give no guarantee of results of product use since conditions of use are beyond our control. Buyers and users are urged to make their own assessment of our products under their own conditions and for their own requirements. If you are a customer, then any contract with you is in accordance with our latest terms and conditions, which are available on request or can be downloaded from this website. Where goods are acquired for business purposes, the Consumer Guarantees Act 1993 does not apply. To the maximum extent permitted by law, we have no liability (whether statutory, in contract or negligence or otherwise) to buyers, users or specifiers of our products for any physical, direct or indirect damage, economic loss or any other loss or costs caused or contributed by us or any of our agents or employees in respect of any goods or services supplied. Also to the maximum extent permitted by law, all conditions and warranties expressed or implied by statute or common law, equity, trade custom or usage or otherwise howsoever are excluded. If, despite this, Stratmore Construction Solutions Limited is found to have any liability, then it is agreed that the liability is limited to the price of the relevant goods or services purchased.